Hydro jetting is a drain cleaning method that uses a stream of water at high pressure to scrub the inside of a pipe. A hose with a specially shaped nozzle is fed into the line through a cleanout or an opened fixture. The nozzle sends jets of water backward to pull itself forward and forward to break up whatever is blocking the pipe. The result is a line that is cleaned along its whole length, rather than a narrow channel opened through one clog.
For a drain that clogs repeatedly, or a line full of grease, scale or roots, that difference is the reason to jet. This page explains what jetting does, what pressure ranges mean in plain terms, how it compares to snaking, whether it is safe for older Kansas City pipes and what the visit looks like.
How hydro jetting works
A jetter is a pump, a water supply and a long hose on a reel. Water comes from a tank on the truck or from a hookup at the property. The pump raises the pressure, and the hose carries it to a nozzle at the end.
Nozzles come in different designs for different jobs.
- Penetrating nozzles send a tight, forward-facing jet to break through a hard blockage.
- Cleaning or scouring nozzles spray mostly backward and outward at an angle. The backward jets pull the hose along the pipe and the angled spray scours the wall.
- Root cutting nozzles and chain heads spin to cut roots and knock down scale. See tree root removal.
The technician feeds the hose in slowly, working back and forth along a stretch of pipe, and the debris is carried downstream by the water. With most blockages the water that gets pushed out is flushed to the municipal sewer. A good jetting job usually ends with the technician pulling the hose out and checking that water flows freely.
What the pressure numbers mean
You will see pressure given in PSI, pounds per square inch, and flow in gallons per minute, GPM. Both matter, and the second is often forgotten. Pressure breaks material loose. Flow carries it away.
In general terms, residential line work is commonly done at pressures in the low thousands of PSI, and heavy commercial and municipal work can run higher. A pressure washer you can buy at a hardware store sits at the low end of that range, but it does not have the hose, the nozzles or the flow for line work. A drain jetter pairs pressure with enough flow to move debris out of a line.
The technician adjusts pressure to the pipe. A thin-walled plastic line gets less pressure than heavy cast iron, and a line of unknown condition gets a gentle start. If someone quotes a very high PSI as a selling point, ask what pressure they would use on your pipe and why. The right answer is the lowest pressure that does the job, not the highest the machine can produce.
What jetting removes
Grease and fat. Kitchen lines in houses and restaurants collect fats that harden as they cool. A cable can cut a hole through grease and leave most of it behind. A jetter strips it off the wall, particularly when heated water is available.
Scale and mineral buildup. Cast iron pipe in older homes grows a rough, crusty lining as it corrodes. That surface catches paper and waste. Jetting with the right nozzle knocks scale down and flushes it away.
Silt, sand and soil. Lines with small cracks or offset joints can admit soil that settles in low spots. Jetting moves it out, though the underlying problem remains and a camera will show it.
Tree roots. Fine roots that have grown into a joint can be cut and flushed with a root cutting head. Large, established roots are a bigger job and may need to be cut repeatedly or the pipe repaired.
General debris. Paper, wipes and soap buildup that a cable would have pushed through or snagged.
Jetting versus snaking
- A single clog in an otherwise clean pipe. A cable is usually fine. Jetting is more than the job needs.
- Grease buildup along the line. A cable opens a channel and leaves the buildup. A jetter cleans the pipe wall.
- Scale in old cast iron. A cable is limited here. A jetter with the right nozzle does the work.
- Roots in a sewer lateral. A cable cuts through and leaves stubs. A jetter with a root head cuts and flushes.
- A line that clogs every few months. A cable is a short-term fix. Jetting lasts longer.
- Fragile or unknown pipe. A cable can snag or damage it. Jetting needs a camera first.
A good technician carries both tools and chooses based on the line. Jetting is not a better snake for every drain. It is the right tool when the problem is buildup along the pipe rather than a single plug. For a simple local clog it may be unnecessary, and you should not be sold jetting for a hairball in a tub.
Camera first
If the line is old, has clogged more than once or has a history nobody knows, a camera inspection before jetting is worth doing. The camera shows whether the pipe is sound enough for water at pressure, where the problem sits and what is in the line. It also gives you a record you can compare against later. See sewer camera inspection.
Sometimes the camera shows a reason not to jet. A collapsed section, a badly offset joint or a pipe so deteriorated it is flaking apart will not benefit from high-pressure water, and may be made worse. In that case the honest answer is a repair or a different cleaning method, not more pressure.
Is jetting safe for old clay and cast iron pipe?
Much of the older housing around Kansas City, including the 1920s through 1950s neighborhoods in Kansas City, Missouri and parts of Johnson County, Kansas, has clay tile or cast iron sewer pipe. The question comes up constantly, and the answer is: usually yes, if the pipe is sound and the pressure is matched to it.
Clay tile. Clay tile lines are made of short sections joined at bell ends. They are strong in compression but cracked or shifted sections, which are common after decades of soil movement and root pressure, can be fragile. A camera shows whether a clay line is intact. On a sound line, jetting at a moderate pressure is a standard method for clearing roots and buildup. On a line with visible cracks, jetting should be careful or avoided, because high-pressure water can widen a gap.
Cast iron. Cast iron is heavy and tough, but it corrodes. A cast iron line that has rusted through in spots may look intact from the inside because scale hides the thin wall. A camera can show the condition, and a technician with experience reads the signs. On sound cast iron, jetting is routine.
Orangeburg and other fiber pipe. Some mid-century houses have a pipe made of bonded fiber. It is soft and deforms with age. Jetting through it needs real caution, and a camera first is not optional.
PVC and ABS. Plastic pipe, common in newer subdivisions, is smooth and handles jetting well. It is also not usually the source of recurring buildup, so jetting there is less often needed.
If a company tells you jetting is safe for any pipe without looking first, that is a warning sign. If they say they want a camera first, that is how it is done right.
When hydro jetting is the better call
- A drain or sewer line that has clogged more than once in a year.
- Grease-heavy kitchen lines, in houses and in restaurants.
- Lines with known roots or scale.
- A home you are about to buy where the sewer scope shows buildup.
- Scheduled maintenance on lines you cannot afford to have back up.
For one-time soft clogs, a cable is often enough and costs less.
What to expect on the visit
You call and describe the problem. We ask where the cleanout is, how old the house is, whether you have had roots or backups before and whether the home is on a slab or has a basement. That helps us bring the right equipment.
On site, the technician looks at the access point and the fixtures. If the line is a candidate for jetting, they usually run a camera first, then set up the jetter, feed the hose into the line and clean it in passes. Water is run to confirm it drains. If a camera was used, they will show you what they saw and discuss anything that needs repair.
Jetting can be messy. Water and debris come back up the line sometimes, so clear a work area and protect the floor. It is also louder than a cable, since the pump runs the whole time.
A jetting visit is a specialty service, and we price it after hearing about the line. Call for a quote.
Jetting for houses, rentals and restaurants
Houses. Homes with older clay or cast iron laterals, mature trees or a history of backups get the most from jetting. A single cleaning can clear a line for years if the underlying pipe is sound, though trees may mean periodic returns.
Rental properties and multi-unit buildings. A shared main line carries every unit's waste, so a backup affects tenants and costs far more than prevention. A scheduled jetting is cheaper than an emergency call and a lost day.
Restaurants and food service. Grease is the problem, and a jetter is the standard tool for grease lines. See commercial drain jetting for how a maintenance schedule works.
We serve Kansas City, MO, Overland Park, KS, Olathe, KS, Lee's Summit, MO and the other cities on the service areas page.
